Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS
Choose a sub category:
JOIST HANGERS FRAMING ANGLES/ANCHORS MENDING PLATES
NAIL PLATES POST ANCHORS / CAPS FENCE BRACKETS
BRIDGING INSULATION SUPPORTS STRAPS
PLYWOOD CLIPS FOUNDATION ANCHORS BRICK/WALL TIES
MISC CONSTR HARDWARE
Sort By:
1 2 3 ... 6
RH Tamlyn BT 22SP Corrugated Straight Brick Wall Tie RH Tamlyn BT 22SP Corrugated Straight Brick Wall Tie, 7/8 in, 1370 lb, 22 ga Steel

Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8". Boxed.

Our Price: $0.08
RH Tamlyn BT22ZZSP Corrugated Scalloped Zig Zag Brick Wall Tie RH Tamlyn BT22ZZSP Corrugated Scalloped Zig Zag Brick Wall Tie, 7/8 in, 1370 lb, 22 ga Steel

Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8".

Our Price: $0.08
RH Tamlyn BT28ZZ5SP Corrugated Scalloped Zig Zag Brick Wall Tie RH Tamlyn BT28ZZ5SP Corrugated Scalloped Zig Zag Brick Wall Tie, 7/8 in, 604 lb, 28 ga Steel

Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8".

Our Price: $0.09
RH Tamlyn BT28500SP Corrugated Straight Brick Wall Tie RH Tamlyn BT28500SP Corrugated Straight Brick Wall Tie, 7/8 in, 604 lb, 28 ga Steel

Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8". Boxed.

Our Price: $0.09
USP Lumber JL26IF-TZ Standard Invert Flange Joist Hanger USP Lumber JL26IF-TZ Standard Invert Flange Joist Hanger, 2 X 6 in, 18 ga T, 695 - 830 lb, Steel

Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.

Our Price: $2.39
USP Lumber JDS24 Double Shear Saddle Purlin Hanger USP Lumber JDS24 Double Shear Saddle Purlin Hanger, 2 X 4 in, 18 ga T, 960 - 1155 lb, Steel

Designed for quick installation of purlins between rafters, joists or trusses in post and beam structures. One-piece construction assures a consistent flush fit between purlin and joist or rafter. A reinforced "double lap" seat boosts the load capacity of this heavy-duty purlin hanger. Requires (4) 10d x 1-1/2" nails for header and (4) 10d" nails for each purlin. Features a 1-9/16" top fold; pending IAPMO-ES evaluation.

Our Price: $4.29
USP Lumber JL28IF-TZ Standard Invert Flange Joist Hanger USP Lumber JL28IF-TZ Standard Invert Flange Joist Hanger, 2 X 8 in, 18 ga T, 930 lb, Steel

Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.

Our Price: $4.59
USP Lumber JUS210-2TZ Double Shear Slant Joint Hanger USP Lumber JUS210-2TZ Double Shear Slant Joint Hanger, 2 in L X 10 in H, 1800 lb, 18 ga Steel

Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.

Our Price: $5.99
RH Tamlyn PC1532 Plywood Clip RH Tamlyn PC1532 Plywood Clip, Aluminum, Mill

With built-in spacer for use when support spacing exceeds the maximum length of an unsupported edge. Boxed.

Our Price: $10.99
RH Tamlyn PCS716 Plywood Clip RH Tamlyn PCS716 Plywood Clip, 20 ga Steel, Galvanized

Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed.

Our Price: $11.99
RH Tamlyn PCS12 Plywood Clip RH Tamlyn PCS12 Plywood Clip, 20 ga Steel, Galvanized

Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed.

Our Price: $11.99
RH Tamlyn PCS1532 Plywood Clip RH Tamlyn PCS1532 Plywood Clip, 20 ga Steel, Galvanized

Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed.

Our Price: $11.99
USP Lumber SKH28R-TZ Skewed Left Joist Hanger USP Lumber SKH28R-TZ Skewed Left Joist Hanger, 2 X 8 - 10 - 12 in, 16 ga T, Steel

Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments.

Our Price: $13.99
USP Lumber SKH28L-TZ Skewed Left Joist Hanger USP Lumber SKH28L-TZ Skewed Left Joist Hanger, 2 X 8 - 10 - 12 in, 16 ga T, Steel

Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments.

Our Price: $13.99
Squeek No More 1011345 Screw Set Squeek No More 1011345 Screw Set, 50 Pieces

Specially scored waxed screws. Scored head breaks off at the same place every time. Carded.

Our Price: $14.99
RH Tamlyn PCS58 Plywood Clip RH Tamlyn PCS58 Plywood Clip, 20 ga Steel, Galvanized

Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed.

Our Price: $14.99
Acorn IHW16100 Insulation Support Wire 16 in L Acorn IHW16100 Insulation Support Wire 16 in L, Carbon Steel

Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.

Our Price: $18.99
USP Lumber NA11-5MC Joist Hanger Nail USP Lumber NA11-5MC Joist Hanger Nail, 8D x 1-1/2 in, 0.131 in Shank, Steel, Hot Dip Galvanized

Structurally rated. For use with MiTek/USP Lumber Connectors' products. For additional information including withdrawal load and allowable shear per nail, please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.

Our Price: $21.99
USP Lumber NA9-5MC Joist Hanger Nail USP Lumber NA9-5MC Joist Hanger Nail, 10D x 1-1/2 in, 0.148 in Shank, Steel, Hot Dip Galvanized

Structurally rated. For use with MiTek/USP Lumber Connectors' products. For additional information including withdrawal load and allowable shear per nail, please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.

Our Price: $21.99
Squeek No More 1010543 Floor Squeak Repair Kit Squeek No More 1010543 Floor Squeak Repair Kit, 53 Pieces

Eliminate squeaks quickly and permanently. Can be applied to 2nd floors, hardwood floors, carpet, and stairs. Each kit contains: 1 - alignment and depth control fixture, 50 - specially scored waxed screws, 1 - special driver bit, 1 - complete instruction kit. Carded.

Our Price: $21.99
Deckmate 90166 Deck Bench Bracket with Bench Bracket Deckmate 90166 Deck Bench Bracket with Bench Bracket, Structural Resin

You determine the size. Connect with railing brackets with 2x4 and 2x6 lumber to easily add a bench to any size or shape deck. Gain increased seating area while using only 7" of deck space. Assembled unit stands 36"H for deck railing, seat is 17"H. Quick and easy to assemble using basic tools. Includes bench bracket, hardware and instructions. LUMBER NOT INCLUDED.

Our Price: $29.99
Acorn IHW24100 Insulation Support Wire 24 in L Acorn IHW24100 Insulation Support Wire 24 in L, Carbon Steel

Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.

Our Price: $29.99
USP Lumber RS20-R Coiled Strap USP Lumber RS20-R Coiled Strap, 1-1/4 in, 1045 lb, 20 ga Steel, Galvanized

Enables cut-to-length convenience for job site needs. G90 galvanizing finish. 1-1/2" nail spacing. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.

Our Price: $29.99
ANGLE 2X4IN TRIPLE ZINC 12GA  ANGLE 2X4IN TRIPLE ZINC 12GA - Case of 15

Provides a 90? connection for medium/heavy duty applications; stronger than angled nailing or screw fastening; help ensure joints are consistently straight and strong.

Our Price: $35.85
Acorn IHW16500 Insulation Support Wire 16 in L Acorn IHW16500 Insulation Support Wire 16 in L, Carbon Steel

Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.

Our Price: $35.99
USP Lumber PA66R Post Anchor USP Lumber PA66R Post Anchor, 6 X 6 in, 18 ga, 470 lb Uplift Douglas Fir, Steel, Galvanized

Used to secure wood posts to concrete footings and to provide moisture damage protection. 4-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Drain slots allow the anchors to shed water. Triple zinc finish for ACQ pressure treated lumber. Not for fence posts or unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes.

Our Price: $39.99
ANGLE 2X6IN TRIPLE ZINC 12GA  ANGLE 2X6IN TRIPLE ZINC 12GA - Case of 15

Provides a 90? connection for medium/heavy duty applications; stronger than angled nailing or screw fastening; help ensure joints are consistently straight and strong.

Our Price: $44.85
USP Lumber JL24 Standard Joist Hanger Joist Hanger 2x4in 20 Gauge - Case of 50

G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.

Our Price: $49.50
Deckmaster DMP125-10 Hidden Deck Bracket Kit Deckmaster DMP125-10 Hidden Deck Bracket Kit, For Use with Deck Boards, 22-1/2 in L

System eliminates the damage to deck boards by hiding all fasteners beneath deckboards. Holds boards tight to eliminate any surface penetration. No moisture can enter deckboards or joists and cause nail penetration. No moisture can enter deckboards or joists and cause nail or screw pop-ups or deck rot. No stains or splinters form around fastener holes. Corrosion resistance. Powder coating's natural wood color blends with the understructure of balconies. For: 3/4" thick boards, composites less than 1-1/8", and any hollowcore composites. Consumer pack includes: 10 brackets, (120) 10 x 1" deck board screws, (110) 8 x 1" joist screws, and a pro bit tip.

Our Price: $54.99
USP Lumber MP34 Framing Angle Frame Angle 1-3/8x2-13/16in gv - Case of 100

Use for joist/header installations. Does not have tabs. G90 galvanizing finish. Requires 8d x 1-1/2 nails. Meets SBCCI, BOCA - NER 505; ICBO 5736; DSA PA-076; Dade County, FL 01-0417.11; and  L.A. City RR25303 codes. 18 Gauge.

Our Price: $59.00
   
 
1 2 3 ... 6