Tight-fitting, high-density foam end plug. To be used in conjunction with VUR ridge vents.

Joint straps for AR10 series aluminum ridge vent. Miami Dade County Approved #NOA 99-0422.04. Nos.ARSBLF, ARSBRF, & ARSWHF Florida Building Code (FBC) Approved FL 5027.

Joint straps for AR10 series aluminum ridge vent. Miami Dade County Approved #NOA 99-0422.04. Nos.ARSBLF, ARSBRF, & ARSWHF Florida Building Code (FBC) Approved FL 5027.

Use under asphalt shingles, metal roofing, cedar shakes or slate; virtually invisible with low-profile design; no baffle to collect debris or clog; HDPE crush-resistant material; adapts to roof pitches 3/12 to 20/12; certified by ICC, BOCA, ICBO, UL CLASS A or C, TDI and Miami Dade county.

Use on roof pitches from 3/12 to 20/12. Helps remove excess heat and moisture to protect against premature roof deterioration and helps prevent problems with birds, insects and animals in attic. Prevents roof rot in attic or roof deck. Minimizes peeling and extends the life of exterior and interior paint. Limits mold growth. Easy to install, shingle over design is virtually invisible when installed. Includes "Smart Nails" for hand-nailing, or 1-3/4" coil nails for nail guns. Meets or exceeds all code requirements. 16.9 sq. ins. per linear foot of net free ventilating area when hand-nailed. 14.1 sq. ins. per linear foot of net free ventilating area when using nail gun. Will not crack or dent during installation. Won't corrode, rust, or turn brittle. Works with traditional size ridge cap shingles.

Tight-fitting, high-density foam end plug. To be used in conjunction with LPR ridge vents.

For all AR10 series ridge vent.

Can be installed with a pneumatic nail gun or hammer. Two coils of 1-3/4" nails provided. External convolute baffles - incurved design allows flexibility to roll up and out while maintaining its shape. Can be cut at one foot intervals - multiple cut lines eliminates unnecessary scrap. Weather protection and performance with no filter to clog. Molded fanfold end plug. Molded centerline. Nail holes marked every 6" - supported every foot. 11 square inches of net free ventilating area per lineal foot. External venturi baffle. Adjusts from 2/12 to 16/12 roof pitches. Limited lifetime warranty- the engineered material guarantees it will last as long as your shingles. Miami Dade County Approved 13-0701.11. 52 CFM at wind velocity of 3 MPH; 148 CFM at wind velocity of 8 MPH; 283 CFM at wind velocity of 15 MPH.

Helps resist snow infiltration in harsh winter climates. Prevent roof rot in attic or roof deck. Minimize peeling and extend the life of exterior and interior paint. Limits mold growth. Allows heat/condensation to escape at most effective location. Shingle-over design blends into ridge line. Watertight, passes 110-MPH wind-driven rain test. External baffles help deflect wind/rain, no end caps needed. 1/8" louver spacing helps keep insects out. Energy-efficient, crush-resistant, with internal structural support for added durability. Flexible 3-point hinge for installation on 3:12 to 16:12 sloped roofs. 40' replaces 18 conventional or ten 12" turbine roof vents. Quick alignment, special tabs for easy, reliable connection. No overdrive, reinforced nail holes. "EasyTear" feature allows product to be hand-torn in 3" increments. Edge overhang allows smooth, continuous coverage between sections. Provides 18 sq.in/linear foot net-free ventilating area. Works with traditional size ridge cap shingles. Boxed.

Shingle-over to blend into ridge line. Allows heat/condensation to escape at most effective location. Watertight, passes 110-MPH wind-driven rain test. External baffles help deflect wind/rain, no end caps needed. Prevents roof rot in attic or roof deck. Minimize peeling and extend the life of exterior and interior paint. Limit mold growth. Specially-designed louver spacing helps keep insects out. Energy-efficient, crush-resistant, with internal structural support for added durability. Extra-flexible hinge design for installation on 3:12 to 16:12 sloped roofs. 3" ring shank nails included to insure proper fastening. Edge overhang for smooth, continuous coverage between sections. Provides 18 sq.in/linear foot net-free ventilating area. 40' replaces 18 conventional or ten 12" turbine roof vents. Hip/ridge compatible with traditional sizes (11-1/2 x 12"). "EasyTear" feature allows product to be hand-torn in 3" increments. Boxed.

Internal aerodynamic curved baffles. 18 square inches of net free ventilating area per lineal foot. External perpendicular omni baffles. Weatherproof under-lapping joint. Four drain holes per foot per side. External venturi baffle. Pre-formed to 3/12 pitch. 10 supported nail holes.  Alignment tabs. External water shield. Slot width guide lines. Adjusts from 2/12 to 16/12 roof pitches. Co-polymer materials. Limited lifetime warranty- the engineered material guarantees it will last as long as your shingles. No connectors required. Molded fanfold end plugs - no accessories or alterations needed. Miami Dade County Approved 16-0510.27. 95 CFM at wind velocity of 3 MPH; 235 CFM at wind velocity of 8 MPH; 430 CFM at wind velocity of 15 MPH; OR4 with nails and OR4 with screen available.

Can be installed with a pneumatic nail gun or hammer. Internal aerodynamic curved baffles. External perpendicular omni baffles. Weatherproof underlapping joint. Four drain holes per foot per side. 11 square inches of net free ventilating area per lineal foot. External venturi baffle. Adjusts from 2/12 to 16/12 roof pitches. Limited lifetime warranty- the engineered material guarantees it will last as long as your shingles. Nail holes marked every 6" - supported every foot. Molded nail lines and centerline. Alignment tabs. External water shield. Slot width guide lines. Molded fanfold end plug. Miami Dade County Approved 13-0701.10. 52 CFM at wind velocity of 3 MPH; 148 CFM at wind velocity of 8 MPH; 283 CFM at wind velocity of 15 MPH.

Maintenance-free all aluminum, aerodynamic profile. Built-in weather baffle, extra wide free flow drainage areas, pre-punched nail holes. Design helps prevent insect, rain and snow infiltration. Base adjustable to broad range of roof pitch 3/12 - 8/12. Dade County Approved 02-0524.01. Nos.AR10BLF, AR10BRF, & AR10WHF Florida Building Code (FBC) Approved FL5027.

Maintenance-free all aluminum, aerodynamic profile. Built-in weather baffle, extra wide free flow drainage areas, pre-punched nail holes. Design helps prevent insect, rain and snow infiltration. Base adjustable to broad range of roof pitch 3/12 - 8/12. Dade County Approved 02-0524.01. Nos.AR10BLF, AR10BRF, & AR10WHF Florida Building Code (FBC) Approved FL5027.

One-piece construction. 3/8" x 1/2" slotted weep holes in wind baffles for water run-off. 1/8" x 1" louvered openings inverted to block weather infiltration. Can be cut to desired length at 2-foot intervals. Pre-notched nail holes. 2" wide nailing flange. Male/female connections - no straps necessary. Adjustable from 3/12 to 12/12 roof pitches. 18 square inches of net free ventilating area per lineal foot. Miami Dade County Approved 16-0510.24. 43 CFM at wind velocity of 3 MPH; 117 CFM at wind velocity of 8 MPH; 221 CFM at wind velocity of 15 MPH.

One-piece construction. 3/8" x 1/2" slotted weep holes in wind baffles for water run-off. 1/8" x 1" louvered openings inverted to block weather infiltration. Can be cut to desired length at 2-foot intervals. Pre-notched nail holes. 2" wide nailing flange. Male/female connections - no straps necessary. Adjustable from 3/12 to 12/12 roof pitches. 18 square inches of net free ventilating area per lineal foot. Miami Dade County Approved 16-0510.24. 43 CFM at wind velocity of 3 MPH; 117 CFM at wind velocity of 8 MPH; 221 CFM at wind velocity of 15 MPH.